SC (Super Capacity) Elevator Bucket

Fabricated Steel

These continuous elevator buckets feature slow-speed, centrifugal discharge. Their three-piece, welded design is fully welded outside and partially welded inside.

Why Steel?

Steel buckets should be substituted for nonmetallic buckets when the heat becomes too excessive or when the bucket elevator carries extremely sharp products.

Features

Available in Stainless Steel and Carbon Steel.

Applications

Aggregate
Cement

Sizes and Dimensions
Technical Information

Measurement Conversion: Imperial Metric

Size (Nominal) Inches	Dimension-Actual (Inches) Tolerance A, B & C ± .25"				Weight, Pounds (Est.)				Capacity ■ Tolerance ± 3%
	Length A	Proj. B	Depth C	Inches D	10 Gauge Steel	.1875" Steel	.25" Steel	.3125" Steel	Gross X-X Cu. Ft.	Y-Y Cu. Ft.
	Length A	Proj. B	Depth C	Inches D	10 Gauge Steel	.1875" Steel	.25" Steel	.3125" Steel	Gross X-X Cu. Ft.	Y-Y Cu. Ft.
12 X 8 X 11	12	8-3/4	11-5/8	4-9/16	22	29	39	49	.54	.35
14 X 8 X 11	14	8-3/4	11-5/8	4-9/16	23	31	41	51	.63	.41
16 X 8 X 11	16	8-3/4	11-5/8	4-9/16	25	34	45	56	.72	.46
18 X 8 X 11	18	8-3/4	11-5/8	4-9/16	27	36	48	60	.81	.52
20 X 8 X 11	20	8-3/4	11-5/8	4-9/16	29	39	52	65	.90	.58
16 X 12 X 17	16	12-7/16	17-3/8	6-1/2	43	58	76	95	1.55	1.11
20 X 12 X 17	20	12-7/16	17-3/8	6-1/2	49	67	88	110	1.94	1.40
24 X 12 X 17	24	12-7/16	17-3/8	6-1/2	55	75	104	130	2.33	1.68
30 X 12 X 17	30	12-7/16	17-3/8	6-1/2	65	88	117	146	2.91	2.11
36 X 12 X 17	36	12-7/16	17-3/8	6-1/2	73	99	132	165	3.49	2.53

■ Tapco recommends using gross x .75, for usable capacity

Size (Nominal) Millimeters	Dimension-Actual (Millimeters) Tolerance A, B & C ± 6.35mm	Weight, Kilograms (Est.)	Capacity (Liters) ■ Tolerance ± 3%
Length A	Proj. B	Depth C	Inches D	10 Gauge Steel	4.76mm Steel	6.35mm Steel	7.93mm Steel	Gross X-X	Y-Y
305 X 200 X 180	305	222	295	116	10.0	13.2	17.7	22.2	15.29	9.91
355 X 200 X 180	356	222	295	116	10.4	14.1	18.6	23.1	17.84	11.61
405 X 200 X 180	406	222	295	116	11.3	15.4	20.4	25.4	20.39	13.03
460 X 200 X 180	457	222	295	116	12.2	16.3	21.8	27.2	22.94	14.72
500 X 200 X 180	508	222	295	116	13.2	17.7	23.6	29.5	25.49	16.42
405 X 300 X 425	406	316	441	165	19.5	26.3	34.5	43.1	43.89	31.43
500 X 300 X 425	508	316	441	165	22.2	30.4	39.9	49.9	54.93	39.64
610 X 300 X 425	610	316	441	165	24.9	34.0	47.2	59.0	65.98	47.57
740 X 300 X 425	762	316	441	165	29.5	39.9	53.1	66.2	82.40	59.75
900 X 300 X 425	914	316	441	165	33.1	44.9	59.9	74.8	98.83	71.64

Style:

SC (Super Capacity)

Design:

Slow speed centrifugal discharge.

Material:

Carbon Steel, Stainless Steel, Aluminum.

Method of Manufacture:

Fabricated.

Standard Construction:

The SC style bucket utilizes a 3-piece design consisting of two end plates and a body. All seams are continuously welded outside and partially inside. The bucket will be produced after Tapco supplies a CAD drawing to be approved by the customer.

Construction Options:

AR plate, wear lips or bead welds.

Material Thickness:

10 ga., 7 ga. (3/16"), 1/4", 5/16", 3/8" and 1/2".

Drilling:

No charge for standard chain drillings.

Venting:

Available on request, contact Tapco for recommendations.

Usable Capacity:

Tapco recommends using 75% of gross, (100%) capacity.

Spacing:

Contact Tapco for recommendations.

Interchangeabilty:

Can be intermixed with existing fabricated SC style buckets. If different weight buckets are mixed in, some care should be taken that the leg does not become too far out of balance. Check elevator for proper clearances. Contact Tapco for recommendations.

Intallation:

Use Grade 5 hex head bolts with hex nuts, flat washers and lock washers. Elevator bolts should not be used on chain attachments.

Caution:

Welding and cutting on elevator legs without taking proper precautions is extremely dangerous and can cause a violent explosion.